How to Remove and also Replace a Bath Tub.
How to Remove and also Replace a Bath Tub.
Blog Article
Listed here below you can locate a lot of exceptional advice involving How to Install a Bathtub Yourself.
Mounting a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, and occasionally, tiling skills. Changing an old tub with a brand-new one is likewise a reasonably challenging task. If the old tub is conveniently easily accessible, the project can move speedily; if you have to open up a wall to eliminate the old bathtub and also position the brand-new bathtub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will require a helper to leave the old tub as well as embeded in the new one. Make certain you have actually qualified yourself for the job as well as fit attempting it. As opposed to employing a contractor to take over a halfway-completed task, it is better to think about using one before you begin. Opportunities are you might need an expert plumber to make tube links.
This write-up will assist you mount a brand-new bathtub in your shower room if you have actually already gotten a brand-new bathtub and also don't need to alter the setup of your previous water system pipelines.
Your tools as well as product list need to comprise the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water. After doing so, turn on the faucets to drain any water staying in the system. The procedure of getting rid of the existing faucets can be fairly problematic due to the restricted gain access to that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the taps. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from turning throughout this process. Once the taps have been removed, the holes in the bath/basin will have to be cleansed of any kind of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washers remain in location between the tap and also the sink. Protect the faucet in position with the maker provided backnut. As soon as the tap is firmly in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet ports. The former type should be linked to the tap ends initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bathtub
Making use of both wood boards under its feet, put the tub in the called for position. The wooden boards are practical in uniformly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by checking the level as well as adjusting the feet on the bath tub until the level checks out level.
To mount faucets, fit the bottom of the outermost versatile faucet port to the ideal supply pipe by making a compression sign up with; after that do the very same for the other faucet.
Switch on the water as well as examine all joints as well as new pipework for leakages and tighten them if essential. Fill the bath tub and additionally check the overflow electrical outlet and the regular outlet for leakages.
Ultimately, fix the bath paneling as defined in the manufacturer's user's manual. Tiling and securing around the bathtub ought to wait up until the bathtub has been made use of at least when as this will settle it right into its final placement.
Preparing for the Installation
To start with, the supporting framework provided with the bathroom must be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the tap features a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps device to stop strain on the bathtub.
Fit the flexible tap ports to the bottom of both taps using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you use all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath need to currently prepare to be suited its last position.
Tiling Around the Bath tub
In the area where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to crack a rigid seal, causing the water to pass through the wall surface in between the bath as well as the tiling, resulting in problems with dampness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your components as well as fittings. They are sold in tubes and cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked paper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to enable the movement experienced when the tub remains in usage. The sealer can break fairly very early if you do not think about this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly readily available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or waterproof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a person who reads about How to Install a Bathtub Yourself, I imagined sharing that blog post was important. Appreciated our review? Please share it. Let other people check it out. I am grateful for your time. Don't forget to check our blog back soon.
Explore Report this page